Table of Contents
Introduction
In order to take apart a BSR record player, there are several steps that need to be followed carefully. It is important to have the right tools and to proceed with caution to avoid damaging any of the components. Here are some general guidelines on how to take apart a BSR record player.
Removing the Turntable Platter
If you’re a vinyl enthusiast, you may have come across a BSR record player at some point. These vintage turntables were popular in the 1960s and 1970s and are still sought after by collectors today. However, if you’re looking to repair or clean your BSR record player, you may need to take it apart. In this article, we’ll guide you through the process of removing the turntable platter from your BSR record player.
Before we begin, it’s important to note that taking apart any electronic device can be dangerous if you’re not careful. Make sure to unplug your BSR record player from the power source before attempting to remove any parts. Additionally, if you’re not confident in your ability to take apart your record player, it’s best to seek the help of a professional.
To remove the turntable platter from your BSR record player, you’ll need a few tools. These include a screwdriver, a pair of pliers, and a soft cloth. Once you have these tools, follow these steps:
1. Remove the rubber mat from the turntable platter. This should come off easily by gently pulling it up from the edges.
2. Locate the C-clip that holds the turntable platter in place. This is a small metal clip that sits in a groove on the spindle. Use your pliers to carefully remove the C-clip by pulling it straight up.
3. Once the C-clip is removed, you should be able to lift the turntable platter off the spindle. However, if the platter is stuck, you may need to gently wiggle it back and forth until it comes loose.
4. With the turntable platter removed, you can now clean it and the spindle. Use a soft cloth to wipe down the platter and remove any dust or debris. You can also clean the spindle with a cotton swab dipped in rubbing alcohol.
5. When you’re ready to reassemble your BSR record player, simply place the turntable platter back on the spindle and replace the C-clip. Make sure the clip is securely in place before using your record player again.
While removing the turntable platter from your BSR record player may seem daunting at first, it’s actually a relatively simple process. With the right tools and a little bit of patience, you can take apart your record player and clean or repair it as needed. Just remember to always be careful when working with electronic devices and seek professional help if you’re not confident in your abilities.
Detaching the Tonearm Assembly
If you’re a vinyl enthusiast, you may have come across a BSR record player at some point. These vintage turntables were popular in the 1960s and 1970s and are still sought after by collectors today. However, if you’re looking to repair or restore a BSR record player, you may need to take it apart. In this article, we’ll guide you through the process of detaching the tonearm assembly.
Before we begin, it’s important to note that taking apart a BSR record player can be a delicate process. If you’re not confident in your ability to do so, it’s best to seek the help of a professional. Additionally, make sure you have the necessary tools on hand, including a screwdriver and pliers.
The first step in detaching the tonearm assembly is to remove the platter. To do so, gently lift the platter off the turntable. If it doesn’t come off easily, check for any screws or clips that may be holding it in place. Once the platter is removed, you should be able to see the tonearm assembly.
Next, locate the tonearm rest. This is the small piece that holds the tonearm in place when it’s not in use. Depending on the model of your BSR record player, the tonearm rest may be located on the side or front of the turntable. Once you’ve found it, gently lift the tonearm and move it to the rest.
Now it’s time to remove the tonearm assembly itself. Start by locating the screws that hold it in place. These are typically located near the base of the tonearm assembly. Use your screwdriver to remove these screws, being careful not to strip them.
Once the screws are removed, you should be able to lift the tonearm assembly off the turntable. However, before you do so, you’ll need to disconnect the wires that connect the tonearm to the rest of the turntable. These wires are typically located near the base of the tonearm assembly and may be held in place by clips or screws.
Use your pliers to gently disconnect these wires, being careful not to damage them. Once the wires are disconnected, you should be able to lift the tonearm assembly off the turntable.
Congratulations, you’ve successfully detached the tonearm assembly from your BSR record player! Now you can clean or repair the assembly as needed. When you’re ready to reassemble the turntable, simply follow these steps in reverse order.
In conclusion, taking apart a BSR record player can be a delicate process, but with the right tools and a little patience, it’s possible to do so successfully. Detaching the tonearm assembly is just one step in the process, but it’s an important one if you’re looking to repair or restore your turntable. Remember to be careful when handling the delicate wires and components, and don’t hesitate to seek professional help if you’re not confident in your ability to do so.
Taking Apart the Motor and Drive System
Taking Apart the Motor and Drive System of a BSR Record Player
If you’re looking to repair or restore a BSR record player, you may need to take apart the motor and drive system. This can be a daunting task, but with the right tools and knowledge, it can be done successfully. In this article, we’ll guide you through the process of taking apart the motor and drive system of a BSR record player.
Before you begin, it’s important to note that taking apart any electronic device can be dangerous. Always make sure the device is unplugged and discharged of any electrical charge before attempting to take it apart. Additionally, if you’re not comfortable working with electronics, it’s best to seek the help of a professional.
The first step in taking apart the motor and drive system of a BSR record player is to remove the platter. This is the circular piece that the record sits on. To remove the platter, gently lift it up and off the spindle. If it’s stuck, you may need to use a platter removal tool or a pair of pliers to gently wiggle it loose.
Once the platter is removed, you’ll be able to see the motor and drive system. The motor is the small, cylindrical piece that powers the turntable. The drive system is the mechanism that connects the motor to the turntable.
To remove the motor, you’ll need to first disconnect the wires that connect it to the rest of the record player. These wires are usually located near the base of the motor. Use a pair of wire cutters or pliers to gently disconnect them.
Next, you’ll need to remove the screws that hold the motor in place. These screws are usually located on the underside of the record player. Use a screwdriver to carefully remove them, being sure not to strip the screws or damage the motor.
Once the screws are removed, you should be able to lift the motor out of the record player. Be sure to keep track of any washers or spacers that may be attached to the motor.
To remove the drive system, you’ll need to first locate the belt. The belt is the rubber band-like piece that connects the motor to the turntable. It’s usually located near the base of the motor.
To remove the belt, gently lift it off the motor and turntable. If it’s stuck, you may need to use a pair of pliers to gently wiggle it loose.
Next, you’ll need to remove the screws that hold the drive system in place. These screws are usually located on the underside of the record player. Use a screwdriver to carefully remove them, being sure not to strip the screws or damage the drive system.
Once the screws are removed, you should be able to lift the drive system out of the record player. Be sure to keep track of any washers or spacers that may be attached to the drive system.
Now that you’ve successfully taken apart the motor and drive system of your BSR record player, you can begin repairing or restoring it. When putting the record player back together, be sure to follow the steps in reverse order. Double-check that all wires are connected properly and that all screws are tightened securely.
In conclusion, taking apart the motor and drive system of a BSR record player can be a challenging task, but with the right tools and knowledge, it can be done successfully. Always remember to take proper safety precautions and seek the help of a professional if you’re not comfortable working with electronics. By following the steps outlined in this article, you’ll be well on your way to repairing or restoring your BSR record player.
Removing the Control Panel and Wiring
If you’re a vinyl enthusiast, you may have come across a BSR record player at some point. These turntables were popular in the 1960s and 1970s and are still sought after by collectors today. However, if you need to repair or clean your BSR record player, you may need to take it apart. In this article, we’ll guide you through the process of removing the control panel and wiring.
Before you begin, make sure you have the necessary tools. You’ll need a screwdriver, pliers, and a soldering iron. It’s also a good idea to have a diagram or photo of the wiring configuration to help you reassemble the turntable later.
The first step is to remove the turntable platter and belt. This will give you access to the motor and wiring underneath. To remove the platter, gently lift it off the spindle. If the platter is stuck, you can use a rubber mat or cloth to grip it and twist it off. The belt should come off easily as well.
Next, you’ll need to remove the control panel. This is where the tonearm and speed controls are located. Look for screws or clips that hold the panel in place. Depending on the model, there may be screws on the top or bottom of the panel, or clips that snap into place. Use your screwdriver or pliers to remove these fasteners.
Once the panel is loose, you’ll need to disconnect the wiring. This is where the soldering iron comes in handy. Look for the wires that connect the tonearm, speed controls, and power switch to the circuit board. Use the soldering iron to melt the solder and disconnect the wires. Be careful not to damage the circuit board or wiring.
If you’re not comfortable with soldering, you can try using wire cutters to snip the wires instead. However, this may make it more difficult to reassemble the turntable later.
Once the wiring is disconnected, you can remove the control panel completely. Set it aside in a safe place where it won’t get damaged.
Now you can access the wiring underneath the turntable. Look for any loose or damaged wires that may need to be repaired or replaced. You can also clean the motor and other components while you have the turntable apart.
When you’re ready to reassemble the turntable, use your diagram or photo to reconnect the wiring. Make sure each wire is connected to the correct terminal on the circuit board. Use your soldering iron to reattach any wires that were disconnected.
Once the wiring is reconnected, you can replace the control panel. Make sure it snaps or screws into place securely. Then, replace the turntable belt and platter.
Congratulations, you’ve successfully removed the control panel and wiring from your BSR record player! With a little patience and the right tools, you can repair and maintain your turntable for years to come.
Disassembling the Cabinet and Base
If you’re a vinyl enthusiast, you may have come across a BSR record player at some point. These vintage turntables were popular in the 1960s and 1970s and are still sought after by collectors today. However, if you want to repair or restore a BSR record player, you’ll need to know how to take it apart. In this article, we’ll guide you through the process of disassembling the cabinet and base of a BSR record player.
Before you begin, it’s important to note that disassembling a BSR record player requires some technical knowledge and skill. If you’re not confident in your abilities, it’s best to seek the help of a professional. Additionally, make sure you have the necessary tools on hand, including a screwdriver, pliers, and a wrench.
The first step in disassembling a BSR record player is to remove the turntable and tonearm. To do this, you’ll need to unscrew the retaining clip that holds the tonearm in place. Once the clip is removed, gently lift the tonearm and set it aside. Next, remove the turntable by unscrewing the retaining clip and lifting it off the spindle.
With the turntable and tonearm removed, you can now focus on disassembling the cabinet and base. Start by removing any screws or bolts that hold the cabinet to the base. These are typically located on the bottom of the unit. Once the screws are removed, gently lift the cabinet off the base and set it aside.
Next, you’ll need to remove the platter and motor assembly from the base. To do this, locate the motor mounting screws and remove them with a screwdriver. Once the screws are removed, lift the motor assembly off the base and set it aside. You should now be able to remove the platter by gently lifting it off the spindle.
With the platter and motor assembly removed, you can now focus on disassembling the base. Start by removing any screws or bolts that hold the base together. These are typically located on the bottom of the unit. Once the screws are removed, gently lift the base off the turntable chassis and set it aside.
At this point, you should have successfully disassembled the cabinet and base of your BSR record player. However, before you start repairing or restoring the unit, it’s important to take note of how everything is assembled. Take pictures or make notes of the order in which the components were removed, as this will make reassembly much easier.
In conclusion, disassembling a BSR record player requires some technical knowledge and skill. If you’re not confident in your abilities, it’s best to seek the help of a professional. However, if you’re up for the challenge, following the steps outlined in this article should help you successfully disassemble the cabinet and base of your BSR record player. Remember to take note of how everything is assembled before you start repairing or restoring the unit.
Q&A
1. What tools do you need to take apart a BSR record player?
– You may need a screwdriver, pliers, and a wrench.
2. How do you remove the turntable from a BSR record player?
– You need to remove the retaining clip or screw that holds the turntable in place, then lift the turntable off the spindle.
3. How do you remove the tonearm from a BSR record player?
– You need to unscrew the tonearm from the base, then disconnect the wires that connect it to the cartridge.
4. How do you remove the motor from a BSR record player?
– You need to unscrew the motor from the base, then disconnect the wires that connect it to the power supply.
5. How do you disassemble the base of a BSR record player?
– You need to remove all screws and bolts that hold the base together, then gently pry apart the different sections of the base.
Conclusion
To take apart a BSR record player, you will need to remove the platter, tonearm, and motor assembly. It is important to be careful and follow instructions or a guide to avoid damaging any components. Once disassembled, you can clean and repair any parts as needed before reassembling the player.
