Table of Contents
Introduction
To change the speed of an orbit record player, there are a few steps that need to be followed.
Adjusting the Belt Tension
Orbit record players are a popular choice for vinyl enthusiasts due to their sleek design and high-quality sound. However, sometimes you may want to change the speed of your orbit record player to match the speed of a particular vinyl record. Fortunately, adjusting the speed of an orbit record player is a relatively simple process that can be done by adjusting the belt tension.
The first step in adjusting the belt tension is to locate the motor pulley and the turntable pulley. The motor pulley is typically located on the underside of the orbit record player, while the turntable pulley is located on the top of the turntable. Once you have located these two pulleys, you will need to remove the platter from the turntable to access the belt.
To remove the platter, gently lift it off the turntable and set it aside. You should now be able to see the belt that connects the motor pulley to the turntable pulley. The belt should be taut, but not too tight. If the belt is too loose, the turntable will spin too slowly, while if the belt is too tight, the turntable will spin too quickly.
To adjust the belt tension, you will need to loosen the motor pulley. This can typically be done by loosening the set screw that holds the pulley in place. Once the set screw is loosened, you can adjust the position of the motor pulley to increase or decrease the tension on the belt.
To increase the tension on the belt, move the motor pulley closer to the turntable pulley. To decrease the tension on the belt, move the motor pulley further away from the turntable pulley. Once you have adjusted the position of the motor pulley, tighten the set screw to hold it in place.
After you have adjusted the belt tension, replace the platter on the turntable and test the speed of the record player. If the speed is still not correct, you may need to make further adjustments to the belt tension until you achieve the desired speed.
It is important to note that while adjusting the belt tension can help you change the speed of your orbit record player, it is not a substitute for a proper turntable setup. To ensure that your orbit record player is functioning at its best, you should also make sure that the turntable is level, the cartridge is properly aligned, and the stylus is in good condition.
In conclusion, adjusting the belt tension is a simple and effective way to change the speed of your orbit record player. By following these steps, you can ensure that your vinyl records are playing at the correct speed and that you are getting the most out of your orbit record player.
Changing the Motor Pulley
Orbit record players are a popular choice for vinyl enthusiasts due to their sleek design and high-quality sound. However, sometimes you may want to change the speed of your Orbit record player to match the speed of a particular vinyl record. Fortunately, changing the speed of an Orbit record player is a relatively simple process that can be done by changing the motor pulley.
The motor pulley is a small, circular component that is located on the motor shaft of the Orbit record player. It is responsible for controlling the speed of the turntable by adjusting the rotation of the motor. By changing the size of the motor pulley, you can adjust the speed of the turntable to match the speed of your vinyl record.
To change the motor pulley on your Orbit record player, you will need a few tools and some basic knowledge of how the turntable works. Here are the steps you need to follow:
Step 1: Turn off the power to your Orbit record player and unplug it from the wall. This will ensure that you do not accidentally damage any of the components while you are working on the turntable.
Step 2: Remove the platter from the turntable by gently lifting it off the spindle. The platter is the circular component that the vinyl record sits on.
Step 3: Locate the motor pulley on the motor shaft. It should be a small, circular component that is attached to the motor shaft with a set screw.
Step 4: Use a small screwdriver to loosen the set screw that is holding the motor pulley in place. Be careful not to lose the set screw as you will need it to secure the new motor pulley in place.
Step 5: Remove the old motor pulley from the motor shaft by gently pulling it off. You may need to use a pair of pliers to grip the motor pulley and pull it off if it is stuck.
Step 6: Install the new motor pulley onto the motor shaft by sliding it onto the shaft and tightening the set screw with a screwdriver. Make sure that the motor pulley is securely attached to the motor shaft.
Step 7: Replace the platter onto the turntable by gently lowering it onto the spindle. Make sure that the platter is seated properly and is not wobbling.
Step 8: Turn on the power to your Orbit record player and test the speed of the turntable by playing a vinyl record. If the speed is not correct, repeat the process of changing the motor pulley until you achieve the desired speed.
In conclusion, changing the speed of an Orbit record player is a simple process that can be done by changing the motor pulley. By following the steps outlined above, you can adjust the speed of your turntable to match the speed of your vinyl record and enjoy high-quality sound from your Orbit record player. Remember to always turn off the power to your turntable and unplug it from the wall before working on any of the components to avoid any accidents.
Replacing the Motor
Orbit record players are a popular choice for vinyl enthusiasts due to their sleek design and high-quality sound. However, sometimes you may want to change the speed of your Orbit record player to match the speed of a particular vinyl record. Fortunately, changing the speed of an Orbit record player is a relatively simple process that can be done by replacing the motor.
The first step in replacing the motor of your Orbit record player is to gather the necessary tools and equipment. You will need a screwdriver, pliers, and a replacement motor that matches the specifications of your current motor. It is important to ensure that the replacement motor is compatible with your Orbit record player to avoid any damage to the turntable.
Once you have the necessary tools and equipment, the next step is to remove the old motor from your Orbit record player. To do this, you will need to remove the platter and the belt that connects the platter to the motor. Use a screwdriver to remove the screws that hold the motor in place and gently lift the motor out of the turntable.
After removing the old motor, it is time to install the replacement motor. Begin by placing the new motor in the same position as the old motor and securing it with the screws. Next, reattach the belt to the motor and the platter. Make sure that the belt is properly aligned and tensioned to ensure that the turntable spins at the correct speed.
Once the replacement motor is installed, it is important to test the speed of your Orbit record player to ensure that it is functioning properly. You can do this by playing a vinyl record and using a strobe disc to check the speed. If the speed is not correct, you may need to adjust the tension of the belt or replace it with a new one.
In conclusion, changing the speed of an Orbit record player is a simple process that can be done by replacing the motor. By following these steps, you can ensure that your turntable is functioning properly and that you can enjoy your vinyl records at the correct speed. Remember to always use caution when working with electronic equipment and to consult a professional if you are unsure about any aspect of the process.
Using a Speed Control Device
Orbit record players are a popular choice for vinyl enthusiasts due to their sleek design and high-quality sound. However, sometimes you may need to adjust the speed of your record player to ensure that your vinyl sounds its best. Fortunately, changing the speed of an orbit record player is a relatively simple process that can be done using a speed control device.
A speed control device is a small electronic device that can be attached to your orbit record player to adjust its speed. These devices are typically sold separately from the record player and can be purchased online or at your local electronics store. They are easy to install and can be used to adjust the speed of your record player in just a few simple steps.
To use a speed control device, you will first need to turn off your orbit record player and unplug it from the power source. Next, you will need to locate the speed control switch on your record player. This switch is typically located on the side or back of the record player and is labeled with the words “33” and “45” to indicate the two different speeds.
Once you have located the speed control switch, you will need to remove the cover from your record player to access the motor. This can usually be done by unscrewing a few screws on the bottom of the record player. Once the cover is removed, you will need to locate the motor and the speed control board.
The speed control board is a small circuit board that is connected to the motor and the speed control switch. To install the speed control device, you will need to disconnect the speed control board from the motor and the switch and connect the speed control device in its place. This can usually be done by simply unplugging the old board and plugging in the new one.
Once the speed control device is installed, you can turn on your orbit record player and adjust the speed using the device’s controls. Most speed control devices come with a dial or knob that can be turned to adjust the speed of the record player. Simply turn the dial or knob until the speed is set to the desired level.
It is important to note that not all orbit record players are compatible with speed control devices. Before purchasing a speed control device, be sure to check the specifications of your record player to ensure that it is compatible. Additionally, some record players may require additional modifications to be made in order to use a speed control device.
In conclusion, changing the speed of an orbit record player is a simple process that can be done using a speed control device. These devices are easy to install and can be used to adjust the speed of your record player in just a few simple steps. However, it is important to ensure that your record player is compatible with a speed control device before making a purchase. With the right equipment and a little bit of know-how, you can ensure that your vinyl sounds its best on your orbit record player.
Upgrading the Turntable’s Electronics
Orbit record players are a popular choice for vinyl enthusiasts due to their sleek design and high-quality sound. However, some users may find that the default speed of their Orbit record player is not to their liking. Fortunately, it is possible to change the speed of an Orbit record player with a few simple steps.
The first step in changing the speed of an Orbit record player is to determine the current speed. Most Orbit record players have two speed settings: 33 1/3 RPM and 45 RPM. To determine the current speed, simply look at the label on the record player or consult the user manual.
Once you have determined the current speed, you can begin the process of changing it. The easiest way to change the speed of an Orbit record player is to upgrade the turntable’s electronics. This can be done by installing a new motor or a new speed controller.
Installing a new motor is a more advanced process that requires some technical knowledge. However, it can be a worthwhile upgrade for those who are serious about their vinyl collection. To install a new motor, you will need to remove the old motor and replace it with the new one. This may require some soldering and wiring, so it is important to follow the manufacturer’s instructions carefully.
A simpler option is to install a new speed controller. This is a device that regulates the speed of the turntable and can be easily installed by anyone with basic technical skills. To install a new speed controller, simply remove the old one and replace it with the new one. Again, it is important to follow the manufacturer’s instructions carefully to ensure that the installation is done correctly.
Another option for changing the speed of an Orbit record player is to use an external speed controller. This is a device that connects to the turntable and allows you to adjust the speed manually. External speed controllers are available from a variety of manufacturers and can be a good option for those who want to experiment with different speeds without making permanent changes to their turntable.
It is important to note that changing the speed of an Orbit record player can have an impact on the sound quality. If the speed is too fast or too slow, the pitch of the music will be affected. It is important to find the right balance between speed and sound quality to ensure that you get the best possible listening experience.
In conclusion, changing the speed of an Orbit record player is a relatively simple process that can be done by upgrading the turntable’s electronics. Whether you choose to install a new motor, a new speed controller, or an external speed controller, it is important to follow the manufacturer’s instructions carefully to ensure that the installation is done correctly. With the right upgrades, you can enjoy your vinyl collection at the perfect speed for your listening pleasure.
Q&A
1. How do you change the speed of an orbit record player?
– You can change the speed of an orbit record player by adjusting the pitch control slider or knob.
2. What is the pitch control slider or knob?
– The pitch control slider or knob is a feature on an orbit record player that allows you to adjust the speed of the turntable.
3. How do you know what speed to set the record player to?
– You should set the record player to the speed indicated on the record label or packaging.
4. What are the common speeds for record players?
– The common speeds for record players are 33 1/3 RPM, 45 RPM, and 78 RPM.
5. Can you damage a record by playing it at the wrong speed?
– Yes, playing a record at the wrong speed can damage the grooves and affect the sound quality.
Conclusion
To change the speed of an orbit record player, you need to adjust the pitch control or speed selector switch. This will allow you to switch between 33 1/3, 45, and 78 RPM speeds. It is important to make sure the correct speed is selected for the record being played to ensure proper sound quality.
